Gtco Summagrid IV - Users Guide Part 1 Manual do Utilizador

Summagrid IV 1 Part 1 Summagrid IV User Information Part 1 explains how to install and run Summagrid IV. It covers all of the basics including, pre

Summagrid IV 10 Preparing the stylus for corded use. 1. Unscrew the cordless endcap. Carefully unplug the lithium battery from its socket by grab

Summagrid IV 11 4. Check the DIP switch settings. The DIP switches are located on the top of the controller. There are three banks of eight switch

Summagrid IV 12 NOTE: To change the DIP switch settings, depress the side of the switch the user wishes to activate using a small screwdriver. Do n

Summagrid IV 13 Chapter 3 Digitizing with Summagrid IV This chapter provides an overview of Summagrid IV, including how the tablet works and informa

Summagrid IV 14 3.1 Operational Overview 3.1.1 Overview Summagrid IV is a digitizer. A digitizer is an input device that translates graphic inform

Summagrid IV 15 resolution. The tablet reports the same coordinates for any point within the square. With different resolution settings, the user

Summagrid IV 16 3.2 Using the Stylus and Cursors 3.2.1 Overview Summagrid IV supports several different stylus and cursor options, which are descri

Summagrid IV 17 Chapter 4 Summagraphics LT Drivers and Utilities (optional) Chapter 4 offers information on using the Summagraphics LT Drivers/Utili

Summagrid IV 18 4.5.3.2 4.6 4.6.1 4.6.2 4.6.3 Diagnostic Tests Option Resetting the Tablet: The UIOFRST Utility Introduction Running UIOFRST from

Summagrid IV 19 4.1 Introduction 4.1.1 Overview This chapter is a guide to using the Summagraphics Drivers/Utilities software. It assumes the user

Summagrid IV 2 Chapter 1 Pre-Installation Considerations The following chapter provides pre-installation tasks that should be completed before insta

Summagrid IV 20 4.2 Summagraphics Driver for Autodesk Applications 4.5.1 Introduction There are two UIOF/Microgrid format drivers for Autodesk appl

Summagrid IV 21 4.2.2 Using DGMG.COM First make sure that DGMG.COM is in the current directory. Then, at the DOS prompt type the following: DGMG

Summagrid IV 22 Disabling the Driver /OFF Disables driver 4.2.3 Examples For a Summagrid IV tablet with a 16-button cursor connected to Com 1 in

Summagrid IV 23 4. If you’re running AutoCAD release 11, select Exit to Main Menu and choose ENTER. 5. Type Y to save configuration changes and p

Summagrid IV 24 number and address of the port in the hexadecimal by choosing the Allow Detailed Configuration option from the configuration menu be

Summagrid IV 25 hexadecimal by choosing the Allow Detailed Configuration option from the configuration menu, then running Configure Digitizer as des

Summagrid IV 26 NOTES:  When using the BA (Base Address) option, all four digits must be specified. Example: Com 1 - \BA03F8  Use the \BA s

Summagrid IV 27 EXAMPLE: TABLETMG \CM2134 The above example shows stylus/cursor switch #2 being mapped to the left mouse button, stylus/cursor sw

Summagrid IV 28 application works only in relative mode and the absolute mode option will have no effect. Other Options /M# /N### Overrides an

Summagrid IV 29 Only TABLETMG.COM can be relocated. TABLETMG.SYS cannot be relocated. The user cannot relocate TABLET.COM into another memory area

Summagrid IV 3 1.1 Pre-Installation Considerations 1.1.1 Checklist of Equipment Below is a checklist of the equipment required for a complete Summ

Summagrid IV 30 sensitivity of the cursor tracking with the /S command option at any time. It is possible to change the parameters of an installed

Summagrid IV 31 1. Insert the Summagraphics Drivers/Utilities diskette into the A: Drive. At the DOS prompt, type the following: A:[ENTER] 2. Ch

Summagrid IV 32 Example: C:\WINDOWS/SUMMA [ENTER] 9. Install the Summagraphics Control Panel icon in one of the program manager groups so that it

Summagrid IV 33 4.4.3 Modifying Driver Defaults with the Control Panel

Summagrid IV 34

Summagrid IV 35

Summagrid IV 36

Summagrid IV 37 4.5 Testing the Tablet: The SG3TEST Utility 4.5.1 Introduction

Summagrid IV 38

Summagrid IV 39

Summagrid IV 4 Chapter 2 Installing Summagrid IV Tablet The following chapter offers basic instructions for setting up Summagrid IV and running the

Summagrid IV 40

Summagrid IV 41

Summagrid IV 42 4.6 Resetting the Tablet: The UIOFRST Utility 4.6.1 Introduction

Summagrid IV 43

Summagrid IV 5 2.1 Pre-Installation Overview 2.1.1 Overview Below are the components that make up a complete Summagrid IV system:  Tablet  PC

Summagrid IV 6 2.2 Installing Summagrid IV 2.2.1 Preparing Summagrid IV for Use 1. Connect Summagrid IV to the computer. Make sure the controll

Summagrid IV 7 Preparing the cursor for cordless use. To prepare either the four or 16-button cursor for cordless use: 1. Remove the battery door

Summagrid IV 8 Preparing the cursor for corded use. To prepare either the four or 16-button cursor for corded use: 1. Remove the battery door from

Summagrid IV 9 The corded transducer is now ready for use with Summagrid IV. Proceed to step four of these installation instructions. NOTE: The cor